« OpenRD f8 samba make | トップページ | FXG-08MK 再度のご臨終 »

2009年10月 8日 (木)

HDL-GX250R kernel make

BAKさめ様のページを参考に、kernel upしてみました。

HDL-GXR>> ext2load ide 0:1 0x02000000 /uImage-2.6.28
Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage-2.6.28

2509220 bytes read
HDL-GXR>> setenv bootargs console=ttyS0,115200 root=/dev/sda2 ro mem=128M
HDL-GXR>> bootm
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.28
   Created:      2009-10-08  22:20:55 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2509156 Bytes =  2.4 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux........................................................................................................................................................... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.28 (root@HDL-GX250R) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Thu Oct 8 21:18:19 UTC 2009
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: I-O DATA HDL-GXR NAS
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda2 ro mem=128M
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 124628KB available (4572K code, 415K data, 132K init)
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
Orion ID: MV88F5182-A2. TCLK=166666667.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
audit: initializing netlink socket (disabled)
type=2000 audit(0.440:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.10)
SGI XFS with security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 243
alg: No test for stdrng (krng)
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:a0:b0:8d:37:42
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
sata_mv sata_mv.0: version 1.24
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 29
ata2: SATA max UDMA/133 irq 29
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: HPA detected: current 312579695, native 312581808
ata1.00: ATA-7: ST3160812AS, 3.AAE, max UDMA/133
ata1.00: 312579695 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST3160812AS      3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312579695 512-byte hardware sectors: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312579695 512-byte hardware sectors: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 00080000 at fff80000
physmap-flash physmap-flash.0: map_probe failed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Marvell Orion EHCI
usb usb1: Manufacturer: Linux 2.6.28 ehci_hcd
usb usb1: SerialNumber: orion-ehci.0
orion-ehci orion-ehci.1: Marvell Orion EHCI
orion-ehci orion-ehci.1: new USB bus registered, assigned bus number 2
orion-ehci orion-ehci.1: irq 12, io mem 0xf10a0000
orion-ehci orion-ehci.1: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Marvell Orion EHCI
usb usb2: Manufacturer: Linux 2.6.28 ehci_hcd
usb usb2: SerialNumber: orion-ehci.1
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver sisusb
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Registered led device: status
Registered led device: error
Registered led device: eSATA1
Registered led device: USB1
Registered led device: USB2
Registered led device: fan
Registered led device: buzzer
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
registered taskstats version 1
rtc-rs5c372 0-0032: setting system clock to 2009-10-08 22:37:54 UTC (1255041474)
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing init memory: 132K
INIT: version 2.86 booting
Activating swap...Adding 1004052k swap on /dev/sda3.  Priority:-1 extents:1 across:1004052k
done.
Checking root file system...fsck 1.40-WIP (14-Nov-2006)
/dev/sda2 has gone 14525 days without being checked, check forced.
/dev/sda2: 48351/18923520 files (2.3% non-contiguous), 886908/37843115 blocks
done.
EXT3 FS on sda2, internal journal
Setting the system clock..
modprobe: FATAL: Could not load /lib/modules/2.6.28/modules.dep: No such file or directory

Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Cleaning up ifupdown....
Loading kernel modules...FATAL: Could not load /lib/modules/2.6.28/modules.dep: No such file or directory
Loading device-mapper support.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)
/dev/sda1: clean, 14/64256 files, 14028/257008 blocks
done.
Setting kernel variables...done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...done.
eth0: link up, 100 Mb/s, full duplex, flow control disabled
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting internet superserver: inetd.
Starting Samba daemons: nmbd smbd.
Starting OpenBSD Secure Shell server: sshd.
Starting FTP server: vsftpd.
Starting periodic command scheduler: crond.
Starting web server (apache2)...apache2: apr_sockaddr_info_get() failed for HDL-GX250R
apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName
.

Debian GNU/Linux 4.0 HDL-GX250R ttyS0

HDL-GX250R login:

HDL-GX250R:~# uname -a
Linux HDL-GX250R 2.6.28 #1 Thu Oct 8 21:18:19 UTC 2009 armv5tel GNU/Linux

HDL-GX250R:~# ls -la /boot/uImage-2.6.28
-rw-r--r-- 1 root root 2509220 Oct  8 22:23 /boot/uImage-2.6.28

|

« OpenRD f8 samba make | トップページ | FXG-08MK 再度のご臨終 »

パソコン・インターネット」カテゴリの記事

コメント

コメントを書く



(ウェブ上には掲載しません)




トラックバック

この記事のトラックバックURL:
http://app.f.cocolog-nifty.com/t/trackback/1224983/31708134

この記事へのトラックバック一覧です: HDL-GX250R kernel make:

« OpenRD f8 samba make | トップページ | FXG-08MK 再度のご臨終 »