« Covia SmartQ5 (Android 日本語版) | トップページ | OpenRD pkg »

2009年10月 3日 (土)

OpenRD 到着

10/2に到着しました。

とりあえず、USBシリアルをDebian機に繋げてbootしてみました。

Debian GNU/Linux squeeze/sid
compay login: xxxx
Password:
Last login: Fri Sep 18 07:36:21 JST 2009 from 192.168.128.86 on pts/0
Linux compay 2.6.30-1-amd64 #1 SMP Mon Aug 3 12:28:22 UTC 2009 x86_64

[   54.012010] usb 2-1: new full speed USB device using uhci_hcd and address 3
[   54.224996] usb 2-1: New USB device found, idVendor=0403, idProduct=9e90
[   54.225046] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   54.225093] usb 2-1: Product: OpenRD JTAGKey FT2232D B
[   54.225142] usb 2-1: Manufacturer: FTDI
[   54.225181] usb 2-1: SerialNumber: FTSDINJR
[   54.225290] usb 2-1: configuration #1 chosen from 1 choice

# modprobe ftdi_sio vendor=0x0403 product=0x9e90

ttyUSB0 ttyUSB1にアタッチされる。。。

# screen /dev/ttyUSB1 115200

ACアダプターを繋げる。

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
_   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/    |____/ \___/ \___/ \__|
** MARVELL BOARD: OpenRD-Client LE

U-Boot 1.1.4 (Apr 22 2009 - 20:18:28) Marvell version: 3.4.16

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE80

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB

Checking for BootROM Routine Errors

No. of BootROM routine retries: 8
NAND: Nand ECC error

Running POST...

        DDR2 data bus test                               PASSED

        DDR2 address bus test                            PASSED

        UART 1 internal loopback test on baudrate   9600 PASSED
        UART 1 internal loopback test on baudrate  19200 PASSED
        UART 1 internal loopback test on baudrate 115200 PASSED

        Device: 0, Size: 512 MB, Page Size: 2 KB, Block Size: 128 KB
        NAND detection test                              PASSED

        Bad Block: 00720000
        Bad Block: 18200000
        Bad Block: 1d800000
        NAND bad-block detection test                    PASSED

        RTC test                                         PASSED

6/6 tests PASSED
POST completed

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is AUDIO
Module 1 is RGMII

USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0

ここで割り込んで、U-bootの環境設定を眺める。

Marvell>>

Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=console=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
ethaddr=00:50:43:01:DE:CD
eth1addr=00:50:43:01:DE:CE
run_diag=no
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw ubi.mtd=1,2048 root=ubi0:rootfs rootfstype=ubifs
bootcmd=nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes

Environment size: 1266/131068 bytes

Marvell>>

OS起動

Marvell>> boot

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.22.18-dirty
   Created:      2009-08-29   9:48:15 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2405724 Bytes =  2.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux...................................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18-dirty (jigar@localhost.localdomain) (gcc version 4.2.1) #1 Sat Aug 29 15:18:06 IST 2009
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw ubi.mtd=1,2048 root=ubi0:rootfs rootfstype=ubifs
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB 0MB 0MB = 512MB total
Memory: 514816KB available (4376K code, 365K data, 140K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....base 10000000, size 256MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- OpenRD-Client  Soc: 88F6281 A0 LE

Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c095d600
PEX0 interface detected Link X1
PCI: bus0: Fast back to back transfers disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: kw_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c0011674)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) Ac 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
XGIfb: Options <NULL>
XGIfb: Relocate IO address: 1000 [00001030]
XGIfb: Enable PCI device
XGIfb: Video ROM usage disabled
XGIfb: SR14=0 DramSzie 200000 ChannelNum 1
XGIfb: Framebuffer at 0xe8000000, mapped to 0xe0c00000, size 2048k
XGIfb: MMIO at 0xec000000, mapped to 0xe0880000, size 256k
XGIfb: XGIInitNew() ...12345678910111215171818118218319202122232425OK
XGIfb: Memory heap starting at 4096K
XGIfb: Using MMIO queue mode
XGIfb: No or unknown bridge type detected
XGIfb: Default mode is 1024x768x16 (60Hz)
Console: switching to colour frame buffer device 128x48
XGIfb: Installed XGIFB_GET_INFO ioctl (80046ef8)
fb0:  frame buffer device, Version 0.8.01
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
RAMDISK driver initialized: 20 RAM disks of 4096K size 4096 blocksize
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload enabled
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Network Fast Processing (Routing) supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Proc tool API enabled
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
    o eth0, ifindex = 1, GbE port = 0
    o eth1, ifindex = 2, GbE port = 1

mvFpRuleDb (dfdc0000): 16384 entries, 65536 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 57 at 0x00720000
Bad eraseblock 3088 at 0x18200000
Bad eraseblock 3776 at 0x1d800000
2 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 2 MTD partitions on "nand_mtd":
0x00100000-0x00500000 : "uImage"
0x00500000-0x20000000 : "rootfs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "rootfs"
UBI: MTD device size:            507 MiB
UBI: number of good PEBs:        4053
UBI: number of bad PEBs:         3
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 4053
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 1/0
UBI: background thread "ubi_bgt0d" started, PID 257
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 7 ports detected
usb 1-1.1: new low speed USB device using ehci_marvell and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
usb 1-1.5: new low speed USB device using ehci_marvell and address 4
usb 1-1.5: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux telephony interface: v1.00
Marvell Telephony Driver:

Warning Tdm is Powered Off
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1     98 MB/s
raid6: int32x2    114 MB/s
raid6: int32x4    123 MB/s
raid6: int32x8    111 MB/s
raid6: using algorithm int32x4 (123 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :  1089.600 MB/sec
   8regs     :   758.400 MB/sec
   32regs    :   904.400 MB/sec
raid5: using function: arm4regs (1089.600 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mvsdmmc: irq =28 start f1090000
mvsdmmc: irq_detect=93
input: HID 04d9:1203 as /class/input/input0
input: USB HID v1.11 Keyboard [HID 04d9:1203] on usb-ehci_marvell.70059-1.1
input: HID 04d9:1203 as /class/input/input1
input: USB HID v1.11 Device [HID 04d9:1203] on usb-ehci_marvell.70059-1.1
input: Logitech Optical USB Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-ehci_marvell.70059-1.5
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
ALSA device list:
  #0: Marvell mv88fx_snd ALSA driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   506507264 bytes (494636 KiB, 483 MiB, 3989 LEBs)
UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format:       4 (latest is 4)
UBIFS: default compressor: zlib
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 140K
Mount failed for selinuxfs on /selinux:  No such device
INIT: version 2.86 booting
                Welcome to Fedora
                Press 'I' to enter interactive startup.
The Hardware Clock does not contain a valid time, so we cannot set the System Time from it.
Unable to set system clock.
Setting clock : Mon Sep 11 00:31:56 EDT 1922 [  OK  ]
Starting udev: [  OK  ]
Setting hostname OpenRD:  [  OK  ]
Checking filesystems
Checking all file systems.
[  OK  ]
Mounting local filesystems:  [  OK  ]
Enabling /etc/fstab swaps:  [  OK  ]
INIT: Entering runlevel: 5
Entering non-interactive startup
Starting sysstat:  Calling the system activity data collector (sadc): Cannot open /var/log/sa/sa11: No such file or directory

[FAILED]
Bringing up loopback interface:  [  OK  ]
Bringing up interface eth0:  [  OK  ]
Bringing up interface eth1:  [  OK  ]
Starting rpcbind: [  OK  ]
Starting NFS statd: [  OK  ]
Starting RPC idmapd: [  OK  ]
Mounting other filesystems:  [  OK  ]
Starting system logger: [  OK  ]
Starting kernel logger: [  OK  ]
Starting system message bus: [  OK  ]
Starting sshd: [  OK  ]
Starting xinetd: [  OK  ]
Network Audio System Release 1.9.1
[  OK  ]
Starting ConsoleKit: [  OK  ]
[  OK  ] crond: [  OK  ]
Starting SMB services: [  OK  ]
Starting Avahi daemon... [  OK  ]

Fedora release 8 (Werewolf)
Kernel 2.6.22.18-dirty on an armv5tejl

OpenRD login:

|

« Covia SmartQ5 (Android 日本語版) | トップページ | OpenRD pkg »

パソコン・インターネット」カテゴリの記事

コメント

コメントを書く



(ウェブ上には掲載しません)




トラックバック

この記事のトラックバックURL:
http://app.f.cocolog-nifty.com/t/trackback/1224983/31624928

この記事へのトラックバック一覧です: OpenRD 到着:

« Covia SmartQ5 (Android 日本語版) | トップページ | OpenRD pkg »